I am replacing the early soft head studs in my engine block and want to run a tap in the block's deck holes before I do , what's the correct thread size and pitch please ? .
TIA ,
MGB Stud Threads ?
- VWNate1
- Veteran Member
- Posts: 1402
- Joined: Sat Sep 05, 2009 7:41 am
- Vehicles Owned: LBC's
Mercedes Diesels OM 616 & 617
1969 Chevrolet C/10 pickup shop truck
250 I-6 , TH350 slushbox
1959 Nash Metropolitan FH Sports Coupe
1961 Morris Minor W/ 1973 1275 CC engine & gearbox
Ural Solo Motos , old Honda 90 CC Tiddlers - Location: Sunny So. Cal. , land of fruits , nuts & flakes
MGB Stud Threads ?
-Nate
- Steve Simmons
- Site Admin
- Posts: 4106
- Joined: Thu Sep 07, 2006 9:45 pm
- Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS - Location: Co-Nay-Ho Valley
- Contact:
Re: MGB Stud Threads ?
UNF 3/8-24
- Larry Kluss
- Veteran Member
- Posts: 1088
- Joined: Wed Jul 25, 2007 12:28 pm
- Vehicles Owned: -
1967 MGB (Works tribute)
1968 E-type Jaguar FHC
1974 Chevy Nova SS (faux)
2000 Ford Ranger XLT
2008 Jaguar XJ L - Location: Conejo Valley
Re: MGB Stud Threads ?
Steve, Are you sure about that? I thought they were coarse 16 pitch threads in the block. I know they are fine 24 pitch on top.
- Steve Simmons
- Site Admin
- Posts: 4106
- Joined: Thu Sep 07, 2006 9:45 pm
- Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS - Location: Co-Nay-Ho Valley
- Contact:
Re: MGB Stud Threads ?
Whoops, I think you're right. I know the nuts are fine thread and that's what I was thinking of. I'll see if I can find a stud around here somewhere. In any case they are standard, not metric, so it should be very easy to figure out which they are by looking at the thread count.
- VWNate1
- Veteran Member
- Posts: 1402
- Joined: Sat Sep 05, 2009 7:41 am
- Vehicles Owned: LBC's
Mercedes Diesels OM 616 & 617
1969 Chevrolet C/10 pickup shop truck
250 I-6 , TH350 slushbox
1959 Nash Metropolitan FH Sports Coupe
1961 Morris Minor W/ 1973 1275 CC engine & gearbox
Ural Solo Motos , old Honda 90 CC Tiddlers - Location: Sunny So. Cal. , land of fruits , nuts & flakes
Re: MGB Stud Threads
Thank you .
I am asking about the 5/15" 16 NC studs that hold the head to the block .
The thinner 3/8" rocker tower studs appear to be O.K. ~ the big ones are stretched and one is stripped so I want to change 'em all and do a good job of it .
I have an American made tap but it really was stiff going into the block's hold in spite of me cleaning the hole well and lubricating the flutes of the tap so I was concerned it maybe had some odd ball thread pitch ? .
No ?
So I should just gently work it into the block's holes then ? .
The stud came out easily so I wonder if maybe I don't need to chase these threads , I still need to find a fill set of 11 dimpled studs , I know where a '77 MGB is sitting way out in the Desert and can go get those but I'd rather grab some off a bare block not take a possibly good (stuck) core 1800 engine apart as once I taker the head off they'll bin it .
What's the current opinion of the Fel-Pro (Payen) black composite head gasket Vs. the copper one I got from Moss Motors ? .
I am asking about the 5/15" 16 NC studs that hold the head to the block .
The thinner 3/8" rocker tower studs appear to be O.K. ~ the big ones are stretched and one is stripped so I want to change 'em all and do a good job of it .
I have an American made tap but it really was stiff going into the block's hold in spite of me cleaning the hole well and lubricating the flutes of the tap so I was concerned it maybe had some odd ball thread pitch ? .
No ?
So I should just gently work it into the block's holes then ? .
The stud came out easily so I wonder if maybe I don't need to chase these threads , I still need to find a fill set of 11 dimpled studs , I know where a '77 MGB is sitting way out in the Desert and can go get those but I'd rather grab some off a bare block not take a possibly good (stuck) core 1800 engine apart as once I taker the head off they'll bin it .
What's the current opinion of the Fel-Pro (Payen) black composite head gasket Vs. the copper one I got from Moss Motors ? .
-Nate
- Steve Simmons
- Site Admin
- Posts: 4106
- Joined: Thu Sep 07, 2006 9:45 pm
- Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS - Location: Co-Nay-Ho Valley
- Contact:
Re: MGB Stud Threads ?
If the studs go in and out easily then I wouldn't worry about it. My feeling is that every time you run a tap through, you're wearing out the threads a little more. If the threads are dirty then I like to run a cleaning brush in there with some solvent and then vacuum it out. But sometimes a chasing tap is inevitable...
I've got a block here but the threads don't look very fresh. I wouldn't use them myself, considering how important they are.
I've got a block here but the threads don't look very fresh. I wouldn't use them myself, considering how important they are.
- VWNate1
- Veteran Member
- Posts: 1402
- Joined: Sat Sep 05, 2009 7:41 am
- Vehicles Owned: LBC's
Mercedes Diesels OM 616 & 617
1969 Chevrolet C/10 pickup shop truck
250 I-6 , TH350 slushbox
1959 Nash Metropolitan FH Sports Coupe
1961 Morris Minor W/ 1973 1275 CC engine & gearbox
Ural Solo Motos , old Honda 90 CC Tiddlers - Location: Sunny So. Cal. , land of fruits , nuts & flakes
Re: MGB Stud Threads ?
Thanks Steve .
I usually just wire brush then oil the upper threads and run the nut up and down to check for stretching , most of these studs do not pass the test .
Do the improved studs have dimples or will they be stamped " 22 " ? .
I usually just wire brush then oil the upper threads and run the nut up and down to check for stretching , most of these studs do not pass the test .
Do the improved studs have dimples or will they be stamped " 22 " ? .
-Nate
- VWNate1
- Veteran Member
- Posts: 1402
- Joined: Sat Sep 05, 2009 7:41 am
- Vehicles Owned: LBC's
Mercedes Diesels OM 616 & 617
1969 Chevrolet C/10 pickup shop truck
250 I-6 , TH350 slushbox
1959 Nash Metropolitan FH Sports Coupe
1961 Morris Minor W/ 1973 1275 CC engine & gearbox
Ural Solo Motos , old Honda 90 CC Tiddlers - Location: Sunny So. Cal. , land of fruits , nuts & flakes
Re: MGB Stud Threads ?
Progress ! .
I got a taper tap and a bottle brush , some Q-Tips and brake cleaner , taped over the cylinder holes and then cleaned and cleaned and cleaned , there was an amazing amount of crud in the bottom of the hole .
I scraped the accumulated carbon and crud off the deck too .
I'm going to use ARP studs , they come with very narrow hardened flat washers , I think I'll use the wider original hardened flat washers and nuts .
Bending over the block kinda hurts my back so it'll be a while before I get back to it but I'm keen to get this done so I can be ready for Summer Driving .
This is a fairly low compression engine so I was thinking of using 45 Lb. Ft. torque ? .
TIA ,
I got a taper tap and a bottle brush , some Q-Tips and brake cleaner , taped over the cylinder holes and then cleaned and cleaned and cleaned , there was an amazing amount of crud in the bottom of the hole .
I scraped the accumulated carbon and crud off the deck too .
I'm going to use ARP studs , they come with very narrow hardened flat washers , I think I'll use the wider original hardened flat washers and nuts .
Bending over the block kinda hurts my back so it'll be a while before I get back to it but I'm keen to get this done so I can be ready for Summer Driving .
This is a fairly low compression engine so I was thinking of using 45 Lb. Ft. torque ? .
TIA ,
-Nate
- Larry Kluss
- Veteran Member
- Posts: 1088
- Joined: Wed Jul 25, 2007 12:28 pm
- Vehicles Owned: -
1967 MGB (Works tribute)
1968 E-type Jaguar FHC
1974 Chevy Nova SS (faux)
2000 Ford Ranger XLT
2008 Jaguar XJ L - Location: Conejo Valley
Re: MGB Stud Threads ?
Nate, I recommend following ARP's installation instructions and using their special lube. Also use their washers and nuts. If you don't, you risk not have the correct tension induced in the studs. This is because ARP threads are precision class 3 and their lube reduces the friction or K factor. The lower the friction factor, the more tension or stretch in the stud at a given torque value. They have calculated the torque based on stud stretch tests, but those values are no good if you change anything involving the joint (i.e. stud/nut/washer, materials, coatings, or the lube). Do not over-torque it either. And be sure to lightly coat both surfaces of the washers. This affects the K-factor too.
Also, use Permatex thread sealer (not silicone or loctite) on the threads into the block and hand tighten (literally). Do not torque or wrench tighten the studs into the block. The stud will not “torque” into the block when the nuts are tightened. The stud will simply pull on the threads and stretch. The reason for the sealer is in case there is porosity in the blind holes in the block. That’s the coolant leak issue I had in one stud hole in my B, before using the sealer. It’s cheap and easy insurance.
For anyone interested, the torque calculation is T=KDP, where T is torque (in-lbs), K-factor (friction coefficient), D nominal bolt/stud diameter (in), and P load/tension (lbs) induced in the bolt or stud. A dry black oxide bolt into a bare steel threaded block has a K-factor of around .23. I believe the K-factor for the ARP lube is probably half of that. All else being equal, that can make a huge difference in the torque need to induce the proper stretch or load into the stud.
Examples: This is only for illustration and not a recommendation for you application.
Using a 3/8” stud and a 5000 pound load into. T=KDP
Using .23 K-factor, .23 * .375 * 5000 = 431 in-lbs (or 36 ft-lbs) torque
Using a lower .12 K-factor, .12 * .375 * 5000 = 225 in-lbs (or 19 ft-lbs) torque
You can see by the above examples that the friction can have a huge impact on the stud load or stretch.
ARP’s has developed their instructions specifically for their product, and I recommend following them.
Also, use Permatex thread sealer (not silicone or loctite) on the threads into the block and hand tighten (literally). Do not torque or wrench tighten the studs into the block. The stud will not “torque” into the block when the nuts are tightened. The stud will simply pull on the threads and stretch. The reason for the sealer is in case there is porosity in the blind holes in the block. That’s the coolant leak issue I had in one stud hole in my B, before using the sealer. It’s cheap and easy insurance.
For anyone interested, the torque calculation is T=KDP, where T is torque (in-lbs), K-factor (friction coefficient), D nominal bolt/stud diameter (in), and P load/tension (lbs) induced in the bolt or stud. A dry black oxide bolt into a bare steel threaded block has a K-factor of around .23. I believe the K-factor for the ARP lube is probably half of that. All else being equal, that can make a huge difference in the torque need to induce the proper stretch or load into the stud.
Examples: This is only for illustration and not a recommendation for you application.
Using a 3/8” stud and a 5000 pound load into. T=KDP
Using .23 K-factor, .23 * .375 * 5000 = 431 in-lbs (or 36 ft-lbs) torque
Using a lower .12 K-factor, .12 * .375 * 5000 = 225 in-lbs (or 19 ft-lbs) torque
You can see by the above examples that the friction can have a huge impact on the stud load or stretch.
ARP’s has developed their instructions specifically for their product, and I recommend following them.
-
- Core Member
- Posts: 440
- Joined: Tue Sep 04, 2007 10:33 am
- Location: LAX
- Contact:
Re: MGB Stud Threads ?
And I was just going to say "don't over torque it wouldn't make any real difference in compression and possibly damage the bolts prematuey". But you said it so much better.
- VWNate1
- Veteran Member
- Posts: 1402
- Joined: Sat Sep 05, 2009 7:41 am
- Vehicles Owned: LBC's
Mercedes Diesels OM 616 & 617
1969 Chevrolet C/10 pickup shop truck
250 I-6 , TH350 slushbox
1959 Nash Metropolitan FH Sports Coupe
1961 Morris Minor W/ 1973 1275 CC engine & gearbox
Ural Solo Motos , old Honda 90 CC Tiddlers - Location: Sunny So. Cal. , land of fruits , nuts & flakes
Re: MGB Stud Threads ?
THANK YOU very much ! .
I did use their torque spec. of 45 # .
I also used their special washers and lubricant .
I got the head on and the water pump in to - day , much thread chasing was done first .
I hope to get back on it this week , I want to drive it to Golden Cove when I get back .
I did use their torque spec. of 45 # .
I also used their special washers and lubricant .
I got the head on and the water pump in to - day , much thread chasing was done first .
I hope to get back on it this week , I want to drive it to Golden Cove when I get back .
-Nate