1967 MGB GT Body and paint

Post your car-related project and restoration stories here!
Post Reply
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

1967 MGB GT Body and paint

Post by Steve Simmons »

As most of you know, my '67 MGB GT was rear-ended a while back. After a lengthy insurance battle, we're finally getting to work. I took the car mostly apart today, and body work will begin this coming Monday.

Here's a photo of the accident damage from my previous thread...

Image

And here is the car as of this afternoon...
MGB GT
MGB GT
bgt.jpg (38.8 KiB) Viewed 83873 times
I'm planning a couple modifications during the bodywork segment of the project. First, I'm getting rid of the seams between the front fenders and cowl. I'm also getting rid of the ones along the top of the rear fenders. If you've seen my MGC GTS up close then you will understand what I mean.

The second modification is to revert the car to the early style door handles, which were a pull handle instead of a push button. I've never been crazy about the look of the push buttons, and wonder why M.G. ever went to them. To accomplish this modification I will have to cut the door handle holes larger in the door skins, and drill two holes to secure the handle. We will then fill the old smaller hole where the small end of the push handle mounted, and drill a new one nearby for the rubber pad the pull handle rests on. The pull handle itself needs to be modified as well, where it touches the door latch actuator.

Monday morning I will be removing the last of the glass and trim, and then we get to work! :hammer:
User avatar
Jimmy
Don't take him seriously!
Posts: 1434
Joined: Tue May 26, 2009 7:25 pm
Vehicles Owned: '74-1/2 MGB
'76 MGB (parts car)
'52 TD
'71 MGB staqtion wagon
'69 MGB (parts car)
'60 Sprite
'79 MG Midget (parts car)
'63 LBC
Plus, a Turbo S (with a damn roof) in the household.
And three Mercedes on 20" wheels.
Location: NM

Re: MGB GT Body and paint

Post by Jimmy »

Would you believe that it was a legal requirement to have the new, "safer" door handles?
By the way, had you not had that obtrusive roof on your car, that Suburban wouldn't have been able to hit anything...its bumper might've cleared a Tourer's trunk lid.
In baseball, running into someone is apparently a "collision".
But doing the same thing in a car somehow makes it an "accident".
User avatar
gorms68
Core Member
Posts: 678
Joined: Sat Jul 26, 2008 8:10 pm
Vehicles Owned: 1914 Chandler model 15
1929 Chandler model 65
1966 MGB roadster
1968 Mustang Dlx coupe
Location: Monrovia

Re: MGB GT Body and paint

Post by gorms68 »

Jimmy wrote:Would you believe that it was a legal requirement to have the new, "safer" door handles?
By the way, had you not had that obtrusive roof on your car, that Suburban wouldn't have been able to hit anything...its bumper might've cleared a Tourer's trunk lid.
That is until it reached the back of their heads :hammer:
Chris Gorman
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: MGB GT Body and paint

Post by Steve Simmons »

I don't think the handle had anything to do with it, but rather the latching mechanism. The later latch had the anti-burst feature, where the early one was merely a pin, as found in the MGA and others.
User avatar
max71
Core Member
Posts: 422
Joined: Sat Jun 02, 2007 9:36 am

Re: MGB GT Body and paint

Post by max71 »

Why did you have to do all the disassembly? Wasn't that included in the paint bill? Or do you save a good bit by doing it yourself? You pulling the glass and gasket, right? Or having them do it?
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: MGB GT Body and paint

Post by Steve Simmons »

I'm trying to save money so I can afford the paint job! The glass will come out, but we're going to hire someone to do it. I don't want to mess with that trim and risk bending it.
User avatar
Jimmy
Don't take him seriously!
Posts: 1434
Joined: Tue May 26, 2009 7:25 pm
Vehicles Owned: '74-1/2 MGB
'76 MGB (parts car)
'52 TD
'71 MGB staqtion wagon
'69 MGB (parts car)
'60 Sprite
'79 MG Midget (parts car)
'63 LBC
Plus, a Turbo S (with a damn roof) in the household.
And three Mercedes on 20" wheels.
Location: NM

Re: MGB GT Body and paint

Post by Jimmy »

Steve Simmons wrote:I don't think the handle had anything to do with it, but rather the latching mechanism. The later latch had the anti-burst feature, where the early one was merely a pin, as found in the MGA and others.
Seems to me that the pull handles went first (they could catch on something), then the un- shrouded pushbutton-mechanism (those could be activated in a collision or rollover).
We are simply very fortunate to have such a caring government looking after us and our automotive well being.
In baseball, running into someone is apparently a "collision".
But doing the same thing in a car somehow makes it an "accident".
User avatar
tannyo
Veteran Member
Posts: 1057
Joined: Wed May 20, 2009 1:58 pm
Vehicles Owned: 1967 MGB GT
Location: North Hollywood, CA
Contact:

Re: MGB GT Body and paint

Post by tannyo »

Jimmy wrote:
Steve Simmons wrote:I don't think the handle had anything to do with it, but rather the latching mechanism. The later latch had the anti-burst feature, where the early one was merely a pin, as found in the MGA and others.
Seems to me that the pull handles went first (they could catch on something), then the un- shrouded pushbutton-mechanism (those could be activated in a collision or rollover).
We are simply very fortunate to have such a caring government looking after us and our automotive well being.
Of course you could lock the doors while you drive. Then if your car does role over the doors won't open and any emergency personal will have to break your door window to get at you. If that happens, a broken door window is probably the least of your problems. :)
User avatar
Jimmy
Don't take him seriously!
Posts: 1434
Joined: Tue May 26, 2009 7:25 pm
Vehicles Owned: '74-1/2 MGB
'76 MGB (parts car)
'52 TD
'71 MGB staqtion wagon
'69 MGB (parts car)
'60 Sprite
'79 MG Midget (parts car)
'63 LBC
Plus, a Turbo S (with a damn roof) in the household.
And three Mercedes on 20" wheels.
Location: NM

Re: MGB GT Body and paint

Post by Jimmy »

Uh, you have to break a window to get out, or to have emergency crew get you out?!?
If they're too stupid to just reach in a grab my carcass, I don't want them to help me.
This reminds me of the joke about the mechanic that was trying to unlock the passenger door and the customer pointed out that the driver's side was already unlocked - to which the mechanic replied "Yeah, I already got that one".

Oh, wait. That's right...those who drive an MGB station wagon can't just exit the vehicle due to that vast expanse of metal on top, where the open air is supposed to be.
Yet another reason to drive the more enjoyable Tourer, I suppose.
In baseball, running into someone is apparently a "collision".
But doing the same thing in a car somehow makes it an "accident".
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: MGB GT Body and paint

Post by Steve Simmons »

We're finally making progress on the car. The paint is currently being stripped and the metal underneath assessed. Unfortunately we uncovered some really bad repair work by a previous welder. There is an ugly panel welded on the lower right-hand door, which was smothered in filler to hide it. The right rear fender also had the lower half replaced, presumably for rust repair, but the seam was left overlapping and rough. There was also some poor repair work done behind the rear bumper but that's hidden so I don't much care.

The REAL mystery however is why a strip was replaced on the left-hand door just below the window. I've never seen an MGB door in need of metal replacement in this location. :? It will need to be properly repaired as well, obviously.

Lastly, we've removed the fender beads from the front fenders and rear fins in favor of welding these seams. This will give a cleaner look, and more importantly eliminate two common breeding grounds for rust.

Not quite as pretty as it once was...
MGB GT being stripped of paint
MGB GT being stripped of paint
stripped.jpg (36.12 KiB) Viewed 83789 times
Ugly patch panel on right-hand door...
Right hand door
Right hand door
rh-door.jpg (29.87 KiB) Viewed 83789 times
Lazy welding job on rear fender...
Rear fender
Rear fender
rhrr-fender.jpg (26.34 KiB) Viewed 83789 times
Lower right hand corner, obviously left rough because it's hidden...
Lower right hand corner
Lower right hand corner
rhrr.jpg (26.22 KiB) Viewed 83789 times
Front fender to main cowl seam without beading...
Front Fender Seam
Front Fender Seam
seam.jpg (36.98 KiB) Viewed 83789 times
Rear fin welded and being smoothed and shaped...
Rear fin
Rear fin
rear-fin.jpg (23.17 KiB) Viewed 83789 times
Left hand door showing mystery patch...
Left hand Door
Left hand Door
lh-door.jpg (36.78 KiB) Viewed 83789 times
Martin Keller
Core Member
Posts: 952
Joined: Tue Sep 18, 2007 10:04 pm
Location: Ventura, Ca.

Re: 1967 MGB GT Body and paint

Post by Martin Keller »

Hi Steve,

Left hand door patch mystery....maybe the Brits were running low on steel for the door skin when they made your car and could not stretch it any further and needed to add some to finish the door... :jester.
That sure is a strange repair. If it was under the wing window I would understand it as the doors are prone to cracking their and the fact that a mirror or mirrors might have been removed from that area under the wing window.
Martin Keller
Ventura, Ca.
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: 1967 MGB GT Body and paint

Post by Steve Simmons »

The body nightmares continue. The left rear fender is worse than the right! It has the same horizontal line except that it isn't even aligned correctly. Bondo and side molding hid the horror. The left rear corner is even worse than the right as well, and we discovered another huge patch panel on the other door down near the bottom. The left fender also had some significant damage just behind the top of the door jam so that will need to be smoothed. I think the metal guy at the shop is cursing the day this car came to them. The good news is that there is almost no rust on the car, even in the seams where the paint was cracking. The cracks were due to the poor body work and lots of filler.
Rear view
Rear view
rear.jpg (41.93 KiB) Viewed 83764 times
No rust
No rust
under.jpg (55.77 KiB) Viewed 83764 times
Thanks to Nate, I have a replacement set of doors so that will save quite a bit of time / money. After sucking the spiders and leaves out of the doors, the first task was to modify the door handle openings to take the earlier style that I so much prefer. I don't know why they ever went away from these handles but I'm sure it had something to do with money.

This modification doesn't require much, but it's a difficult job to get the opening just right and there isn't much room for error. The later doors were never meant for this handle. Long story short, you have to enlarge the handle opening, cut off the trigger from the handle, install an adjustable bolt in its place, fill in the forward hole for the old handle, drill a new hole next to it for a rubber buffer pad, and drill two small holes in the door jam area to secure the new handle. You also need to cut back the stiffening plate that is welded to the door behind the latching mechanism, and relieve the handle slightly in this area, to prevent the chance of it hanging up. It's pretty tight in there.

Normally I don't like doing permanent mods to a car's metalwork but this wouldn't be a hard job to return - just one small patch and fill three tiny holes. I can't imagine anyone going back to the old style of handle anyway.
Old hole
Old hole
hole1.jpg (24.45 KiB) Viewed 83764 times
New hole
New hole
hole2.jpg (31.16 KiB) Viewed 83764 times
Old handle
Old handle
old-handle.jpg (27.73 KiB) Viewed 83764 times
New handle
New handle
new-handle.jpg (37.11 KiB) Viewed 83764 times
Yes, I know the new hole looks crooked but that's part of what makes it difficult. The two holes are actually angled slightly differently so you can't use the old one as a guide. You also can't use an old roadster door as a pattern for a GT door because the early roadster door is unique and totally different in every dimension from a GT door.

Onward and upward! :)
User avatar
gorms68
Core Member
Posts: 678
Joined: Sat Jul 26, 2008 8:10 pm
Vehicles Owned: 1914 Chandler model 15
1929 Chandler model 65
1966 MGB roadster
1968 Mustang Dlx coupe
Location: Monrovia

Re: 1967 MGB GT Body and paint

Post by gorms68 »

Looking good Steve. Glad you have the car in a shop that can handle the unexpected issues you have uncovered. Do you still need a bonnet?
Chris Gorman
Stewart
Core Member
Posts: 687
Joined: Tue Aug 07, 2007 4:56 pm
Vehicles Owned: 1966 2cv
1967 mgb gt sc
1975 mgb sc
1973 1800es
1972 Citroen ID21 wagon
Location: Santa Barbara CA

Re: 1967 MGB GT Body and paint

Post by Stewart »

update?
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: 1967 MGB GT Body and paint

Post by Steve Simmons »

Chris, not sure yet because it's for the '65, which is on hold... again. If you're going to get rid of it, let me know first though, please!

Update: Not much progress. I was out of town for two weeks and I came back to find the car was not in primer like it was supposed to be by now. Apparently a guy with a Stingray Vette was desperate to get his car back so they moved him to the front of the line. It was sprinkling on the day of the show so he didn't take the car anyway. :x

The car's condition as of Monday...
Bare metal MGB GT
Bare metal MGB GT
IMAG0893.jpg (43.01 KiB) Viewed 83719 times
On the bright side, this cool Lincoln was in the shop while I was there...
Lincoln
Lincoln
1.jpg (60.09 KiB) Viewed 83717 times
Lincoln
Lincoln
2.jpg (47.62 KiB) Viewed 83717 times
Lincoln
Lincoln
3.jpg (58.21 KiB) Viewed 83717 times
User avatar
gorms68
Core Member
Posts: 678
Joined: Sat Jul 26, 2008 8:10 pm
Vehicles Owned: 1914 Chandler model 15
1929 Chandler model 65
1966 MGB roadster
1968 Mustang Dlx coupe
Location: Monrovia

Re: 1967 MGB GT Body and paint

Post by gorms68 »

Steve I have three bonnets now, two hanging on the wall, one loosely fitted to the GT. I plan to keep the best of the three for the GT. The other two will be available to sell or for that future project down the road. You can have dibs on one of them.
Chris Gorman
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: 1967 MGB GT Body and paint

Post by Steve Simmons »

Not a lot to report, but the new doors and hatch are in place and are being fitted to the car. One door had been opened too far at some point in the past and was damaged, but that has been mostly repaired. The right rear lower quarter panel was replaced during restoration and it was welded poorly, and protrudes way too far from the lower sill, so the door sits way too far inboard. I have no idea how they got the old door to line up but this panel will have to be cut off and re-welded properly. The left rear quarter is also welded poorly and will have to be cut off and fixed also.

The new rear hatch is starting to fit beautifully now that the hinge area oft he rook has been straightened. The right side still sits slightly too high, so the body will probably be pulled up slightly there to get it aligned just right. There is also evidence that the left rear pillar was slightly bent as I had originally feared, but it's all metal so it can be pulled easily. The shop will be fitting the rear windows soon to make sure it's all fitting properly.

As the car sits now
MGB GT in body shop
MGB GT in body shop
IMAG0988.jpg (62.36 KiB) Viewed 83688 times
The right rear fender sitting proud at the bottom of the door jam
IMAG0994.jpg
IMAG0994.jpg (49.25 KiB) Viewed 83688 times
Some of the poor welding on the left rear quarter, in the lower door jam
IMAG0998.jpg
IMAG0998.jpg (61.42 KiB) Viewed 83688 times
Left side, note more poor welding along the seam of that rear quarter, and nearly repaired door skin
IMAG1000.jpg
IMAG1000.jpg (58.6 KiB) Viewed 83688 times
The hatch installed and mostly fitted
IMAG1001.jpg
IMAG1001.jpg (57.15 KiB) Viewed 83688 times
The gap on the right side which still needs to be addressed
IMAG1003.jpg
IMAG1003.jpg (74.31 KiB) Viewed 83688 times
Typical rust holes on most MGB GTs, where the fin meets the rear window and rain gutter
IMAG1006.jpg
IMAG1006.jpg (70.47 KiB) Viewed 83688 times
Right side, note the poor fit of the fender at the bottom of the door, and the crappy welding along the seam.
IMAG1007.jpg
IMAG1007.jpg (46.64 KiB) Viewed 83688 times
User avatar
Larry Kluss
Veteran Member
Posts: 1087
Joined: Wed Jul 25, 2007 12:28 pm
Vehicles Owned: -
1967 MGB (Works tribute)
1968 E-type Jaguar FHC
1974 Chevy Nova SS (faux)
2000 Ford Ranger XLT
2008 Jaguar XJ L
Location: Conejo Valley

Re: 1967 MGB GT Body and paint

Post by Larry Kluss »

Looks like good progress to me, Steve. It will be quite nice and properly done when finished.
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: 1967 MGB GT Body and paint

Post by Steve Simmons »

Finally in primer!
Attachments
MGB GT
MGB GT
primer.jpg (46.35 KiB) Viewed 83553 times
User avatar
Jimmy
Don't take him seriously!
Posts: 1434
Joined: Tue May 26, 2009 7:25 pm
Vehicles Owned: '74-1/2 MGB
'76 MGB (parts car)
'52 TD
'71 MGB staqtion wagon
'69 MGB (parts car)
'60 Sprite
'79 MG Midget (parts car)
'63 LBC
Plus, a Turbo S (with a damn roof) in the household.
And three Mercedes on 20" wheels.
Location: NM

Re: 1967 MGB GT Body and paint

Post by Jimmy »

Primer?
It looks just like the color it was before.
In baseball, running into someone is apparently a "collision".
But doing the same thing in a car somehow makes it an "accident".
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: 1967 MGB GT Body and paint

Post by Steve Simmons »

Good. Then if I scratch the paint, it will be easier to buff out. The primer is actually lighter and much more silver than the paint itself.
User avatar
Jimmy
Don't take him seriously!
Posts: 1434
Joined: Tue May 26, 2009 7:25 pm
Vehicles Owned: '74-1/2 MGB
'76 MGB (parts car)
'52 TD
'71 MGB staqtion wagon
'69 MGB (parts car)
'60 Sprite
'79 MG Midget (parts car)
'63 LBC
Plus, a Turbo S (with a damn roof) in the household.
And three Mercedes on 20" wheels.
Location: NM

Re: 1967 MGB GT Body and paint

Post by Jimmy »

Perfect. Lighter equals better performance, right?
That's yet another reason I don't like black cars.
In baseball, running into someone is apparently a "collision".
But doing the same thing in a car somehow makes it an "accident".
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: 1967 MGB GT Body and paint

Post by Steve Simmons »

PAINT!!! :drive
Attachments
MGB GT Painted
MGB GT Painted
paint1.jpg (71.68 KiB) Viewed 83429 times
MGB GT Painted
MGB GT Painted
paint2.jpg (61.55 KiB) Viewed 83429 times
User avatar
gorms68
Core Member
Posts: 678
Joined: Sat Jul 26, 2008 8:10 pm
Vehicles Owned: 1914 Chandler model 15
1929 Chandler model 65
1966 MGB roadster
1968 Mustang Dlx coupe
Location: Monrovia

Re: 1967 MGB GT Body and paint

Post by gorms68 »

Looks like primer :devil:

So how long before your are driving the GT again?
Chris Gorman
User avatar
Steve Simmons
Site Admin
Posts: 4106
Joined: Thu Sep 07, 2006 9:45 pm
Vehicles Owned: .
1937 MG SA Saloon
1946 John Deere AN
1949 MG TC
1953 MG TD
1958 MGA Roadster
1959 Morris Minor 1000
1965 MGB
1967 MGB GT (UK-Spec)
1967 Austin Healey 3000 BJ8
1969 MGC GTS
Location: Co-Nay-Ho Valley
Contact:

Re: 1967 MGB GT Body and paint

Post by Steve Simmons »

Bastage! :lol:

I should be driving it daily again by next week. The shop is going to install the trim, front and rear windows. Then I'll have to install bumpers, door mechanisms, side glass, etc. Plus I need to finish the pull handle mod. I figure I'll be picking it up by the weekend if all goes well, and then get the final bits installed over the next day or two.
Post Reply